For the purpose of this article I'm going to assume that everyone knows the basics of how to build a SIP trunk on all three platforms. I will also assume that the appropriate licenses have been purchased and that the BCM is SIP capable.
Let's start with the CS1000. The NRS needs to be configured You will need to create endpoints for the BCMs and IP Offices, as well as any CS1000 locations that you have. The IP Office and BCM endpoints must be configured as static SIP endpoints.Routing entries need to be created for each endpoint to correspond with your dialing plan. It may seem obvious, but you need to build SIP trunks and routes from the CS1000. It is very important to note that the IP Office must be configured in Proxy Mode. The IP Office does not support Redirect Mode. Once you have finished with this you are done with the easy part.
The BCM configuration is also quite easy. Build your SIP trunks on the BCM. Configure your SIP domain and enable RTP keepalives. Calls will be routed on the Private network, so navigate to the Private tab under SIP Trunking. Ensure that your URI map matches the URI Map on your node:
And now on to the fun piece. Configuring the IP Office is the most time consuming part of the whole setup. You need to configure three items: SIP Lines, Incoming Call Routes, and Short Codes.
For your SIP Lines you need a connection to each networked system. For simplicity I chose to use the same incoming call route, however the Line Group ID needs to be different for each site. In my example I used SIP Lines 17-20. All my Incoming Call Groups were 17, however I matched up the Line Group ID with the line number. Since these are IP trunks you can configure them however you like as long as they don't interfere with any other lines in the system. For the SIP line to the CS1000 use the Node IP address. For the BCM SIP Lines use the IP address of each individual BCM. Configure each SIP line with the maximum number of calls equal to the maximum number of SIP Line licenses in the system. This way each site is capable of having the maximum number of VoIP calls, as long as no other licenses are in use.
If you used the same incoming call route for each SIP trunk you only need to create a single incoming call route for IP calls. For the destination use a period (.) to have the call sent to whichever digits are being sent from the far end.
In order to make outgoing calls work you need to create short codes on the system to match the dialing plan. In my case we had four-digit dialing with each site having a unique first digit. This made it easy, I configured a short code for each first digit (i.e. 1XXX, 2XXX, 3XXX, etc.). Each short code was configured as Dial 3K1 using the appropriate line group for the far end site. The BCMs will not understand the standard dial string sent by the IP Office so you need to configure the phone context in the telephone number. In my example I showed the Private/CDP URI as cdp.udp so I needed the following Telephone Number in my short code:
.";phone-context=cdp.udp"
Once all of this is done just go ahead and commit your changes to the IP Office. It will probably require a reboot as you are changing IP information. Once everything comes up go ahead and make your test calls and give the customer a big smile on your way out the door, you're their hero.
As always feel free to comment if you have any questions. I'll always do my best to help!
As always feel free to comment if you have any questions. I'll always do my best to help!
Did you get Caller Name ID working both ways between the CS1000 & IPO? I mean both ways so that both caller and recipient see the extension and name of the the other person and regardless of who initiates the call?
ReplyDeleteI have IPO 9.0 connected to CS1000 7.5 and am having issues with the CS1000 phones not seeing the name display. But the 9600 phones on IPO see the CS1000 caller names just fine.
There are a couple things you could look at:
DeleteOn the SIP Line what do you have for Send Caller ID? If it's None you will get caller ID withheld
The SIP URI is used for outbound calls. Ensure that your SIP URI has the Display Name configured to use a valid source. I usually select Use Internal Data, however you need to ensure that the user is configured correctly. Check the SIP tab of the user.
If you continue to have problems let me know. I'd be happy to take a look at some traces and your config to figure out what is happening.